Hsiuping University of Science and Technology Institutional Repository : Item 310993100/2260
English  |  正體中文  |  简体中文  |  全文笔数/总笔数 : 4334/7631
造访人次 : 3191010      在线人数 : 228
RC Version 3.2 © Powered By DSPACE, MIT. Enhanced by NTU Library IR team.
搜寻范围 进阶搜寻

jsp.display-item.identifier=請使用永久網址來引用或連結此文件: http://ir.hust.edu.tw/dspace/handle/310993100/2260

题名: L型彎曲製程中折疊區圓孔的彎曲特性之分析與建模
Analysis and modeling of the bending performances of the circular holes in the fold zone duringthe L-shape bending process
作者: 陳世峯
贡献者: 精密機械與製造科技研究所
关键词: L型彎曲過程
反應曲面法(RSM)
中央合成設計(CCD)
回彈角
日期: 2010-07
上传时间: 2011-05-23T06:52:23Z
摘要: 本文研究，著重於平板 L型彎曲製程中折疊區有孔之實驗已完成。應用反應曲面法(RSM)，提出有系統且完整的實驗設計與分析方法。實驗設計採用中央合成設計法(CCD)，設計 4個獨立變數包含工件厚度、模具彎角半徑、孔徑和孔數作為設計參數。同時已完成探討，在 L型彎曲製程中對於回彈角及圓孔變形率的研究。頂面切線方向沿上表面軸向變形，底面軸方向沿下表面切線方向變形，其變數名稱分別為 RD_A、RD_T、Rd_a、Rd_t，結果顯示，回彈角會隨著孔之尺寸、模具彎角半徑、孔數的減小及工件厚度的增大而減小。其變形率，RD_A、RD_T 、 Rd_a、 Rd_t 會隨著模具彎角半徑的減小或增加工件厚度將會有較高之變形率。此外，上述之討論也會隨孔之尺寸和孔數的增加使所有的變化減少。本研究使用RSM的方法得到明確的二階數學公式，在有關回彈角與RD_A、RD_T、Rd_a及Rd_t實驗值與預測值影響變化之比較，其最大誤差分別為4.24％、4.30％、4.52％、4.7％和 4.21％。
In this study, a series of experimental investigation focusing on the folded zone of the plates with holes in the L-bending process have been performed. On the basis of the response surface method (RSM), a set of complete, systematic experimental design and analysis method have been proposed. The experimental design adopts the central composite design (CCD). Also, four independent variables, including thickness of work pieces, die corner radius, hole diameter and the number of holes, are regarded as the design parameters in the experimental design. The value of springback angle and the shape deformation of holes in the L-bending process also have been explored in the meanwhile. The results reveal that the value of springback angle increases with increasing the size of hole and die corner radius, and decreases with increasing the thickness of work pieces. The deformation rate along the axial direction on the top surface, the tangent direction on the top surface, the axial direction on the bottom surface and the tangent direction on the bottom surface are designated as RD_A , RD_T, Rd_a, Rd_t, respectively. According to the experimental results, to reduce the die radius or increase the thickness of work pieces will cause a high deformation rate. In addition, the variation of RD_A , RD_T, Rd_a and Rd_t will decrease with the increase of the hole diameter and the number of holes. Using the RSM method with a quadratic explicit formulas, the maximum deviations of the predicted values of relevant influencing parameters in terms of the springback angle, the variation of RD_A , RD_T, Rd_a and Rd_t, which are compared with the actual experimental data, are 4.24%, 4.30%, 4.52%, 4.79% and 4.21%, respectively.
描述: 指導教授：洪振聰 博士
显示于类别:[機械工程系(含精密機械與製造科技碩士班)] 學位論文

文件中的档案:

档案 大小格式浏览次数
index.html0KbHTML513检视/开启

在HUSTIR中所有的数据项都受到原著作权保护.

 

DSpace Software Copyright © 2002-2004  MIT &  Hewlett-Packard  /   Enhanced by   NTU Library IR team Copyright ©   - 回馈